Daily Blog Post 1

 5/9/22 at 7:22 pm. 

Hours Today: 4 Hours 50 minutes

Total Hours: 4 Hours 50 minutes

Today I worked on a few different steps of my boat build. One that I have become incredibly familiar with is sanding. The interior of the boat needs to be coated a minimum of two times with unthickened epoxy. When I sand through the epoxy layer, I need to patch it with more and sand again. By today, I had finished my second coat and was sanding the places that I needed to patch. I then moved onto my seats, and sanded those smooth. The seats also needed two coats on the bottom before they get installed, because there would be no way to do so once they are on the boat. I then vacuumed the boat out, and dry fit my seats. I will need to make sum adjustments to the stern seat, although the cockpit seat and bow seat seem to fit as they should. I didn't get into the shop as early as I was hoping, so I only logged 4 hours and 50 minutes today. Tomorrow I will work on further patching and fitting the cockpit seat. 

Comments

Post a Comment

Popular posts from this blog

Blog Post #9

 5/21/22 I returned to campus yesterday, and got right to work this morning. It was a somewhat light day in terms of work, but I was able to knock out some more of the important prep work. I began by removing all of the spring and C clamps that I used to affix the second set of rubrails. There were a handful that were stuck by epoxy squeeze out, but they were nothing that couldn't be taken care of with the heat gun.  There were also a number of clamps that I needed tighten a little more aggressively, due to the warp in the rail. With this in mind, I cut a small 1x1 squares of wood to place between the clamp where it met the hull. Having one of these squares on either side of the clamp allowed me to tighten the clamps without worrying about damaging the wood. Once all clamps were removed, I repeated the same process I discussed finishing the first set of rubrails. Using a heat gun and chisel, I scraped the majority of the squeeze out. This time, however, I also took care of the...
Read more

Blog Post #4

 5/12/22 Hours Today: 8 Hours 30 minutes Total Hours: 29 Hours Today was a longer day, and I started it with sanding the hull in preparation for another coat of epoxy. I realised, however, that I still needed to install the skeg. If I installed it prior to sanding and coating, the fillets would have more time to cure. With this in mind, I measured the center of the hull from stern to bow, and marked lines 3/8 of an inch on either side. The width of the skeg is 3/4 of an inch, so these lines would allow me to line it up perfectly upon installation.  The next step was for me to mark and drill 4 pilot holes through the bottom of the hull, in increments of 10 inches. Beginning at10 and ending at 40 inches, I used a 1/8 inch drill bit and followed the path the skeg will take. I then got underneath the boat, and countersunk all of the holes. This allows the screws to sit flush with the deck.  I got someone to hold the skeg in place while I conducted a "dry fit", in which I set ...
Read more

Blog Post #6

 5/14/22 Hours Today: 4 Hours 30 minutes Total Hours: 40 Hours Today was yet another day comprised mostly of sanding. To begin the day, I sanded the final coat of epoxy on the hull using an orbital sander.  Then, with the faithful sanding block, I roughed up the coat on the skeg and the skids. The skeg will need one more coat, whereas the skids will need two. This is not where the work on the skids will end though. I decided to run very small fillets along the sides of the skids, that way they will be protected from any water working its way into the gap. I also need to fill the cracks, which may be something I take care of tomorrow.  After 3 or 4 hours working on the boat, I decided today would be a good time to go to the hardware store and get some paint. I went to Ace Hardware in Franklin, because they seemed to have the cheapest paint and the largest variety. The paint I will be using is the store's version of Rust-oleum, which is a brand of indoor outdoor paint that ...
Read more